Estimated reading time: 11 minutes
Table of Contents
- Why Your Bench Press Is Stalling
- The 5 Keys to a Bigger Bench Press
- The Perfect Bench Press Setup
- Technique Breakdown
- How to Programme for Bench Press Growth
- Best Accessory Exercises for Bench Press
- Sample 4-Week Bench Press Block
- FAQ
- External Resources
Why Your Bench Press Is Stalling
Bench press plateaus are the most common complaint among intermediate lifters at Powerlifting Australia state meets in Sydney and Melbourne and GPC competitions in Brisbane and Perth. The usual culprits:
- No real progressive overload — training the same weight for weeks
- Poor setup — losing leg drive, shoulder position, or bar path
- Insufficient volume or frequency
- Weak accessory muscles (triceps, upper back, front delts)
- Inadequate recovery between bench sessions
The 5 Keys to a Bigger Bench Press
| # | Key | Why It Matters |
|---|---|---|
| 1 | Progressive Overload | Without it, there is no stimulus to get stronger |
| 2 | Leg Drive | Creates full-body tension and increases force production |
| 3 | Arch & Tuck | Shortens the range of motion and protects the shoulder |
| 4 | Grip Width | Optimises force transfer and elbow angle |
| 5 | Pause Reps | Eliminates bounce, builds starting strength off the chest |
The Perfect Bench Press Setup
- Feet flat on the floor — drive into the floor through your whole session
- Shoulder blades retracted and depressed — pull them together and down, create a stable shelf
- Natural arch in the lower back — not exaggerated, just enough to create tension
- Bar over lower chest at the bottom — not over the face or upper chest
- Elbows at 45-75 degrees — not flared at 90, not tucked to your sides
- Full leg drive throughout — not just at lockout
Technique Breakdown
Grip Width
Most Powerlifting Australia and GPC competitors grip at or near the legal maximum (81cm ring marks). A wider grip shortens the range of motion; a narrower grip shifts more load to the triceps. Experiment within the 70-81cm range to find your strongest position.
Bar Path
The bar should touch your lower chest and travel in a slight diagonal arc, not straight up and down. Press the bar back toward the rack as you drive it up.
Breathing and Bracing
Take a deep breath before unracking. Brace your core hard. Hold that brace for the entire rep. Do not exhale at the bottom — you will lose tension.
How to Programme for Bench Press Growth
| Level | Frequency | Weekly Volume | Progression |
|---|---|---|---|
| Beginner | 2-3x/week | 9-12 sets | +2.5kg per session |
| Intermediate | 3x/week | 12-16 sets | +2.5kg per week |
| Advanced | 3-4x/week | 16-20 sets | +1.25-2.5kg per block |
Best Accessory Exercises for Bench Press
- Close-grip bench press — tricep-dominant, carryover to lockout
- Incline dumbbell press — upper chest and front delt volume
- Tricep pushdowns — high-rep tricep isolation
- Face pulls — rear delt and rotator cuff health
- Rows (barbell or cable) — upper back strength, shoulder stability
- Floor press — eliminates leg drive, targets lockout weakness
Sample 4-Week Bench Press Block
| Week | Main Bench | Focus |
|---|---|---|
| Week 1 | 4x5 @ 75% 1RM | Volume baseline |
| Week 2 | 4x4 @ 80% 1RM | Intensity increase |
| Week 3 | 5x3 @ 85% 1RM | Heavy stimulus |
| Week 4 | 3x3 @ 70% 1RM | Deload |
FAQ
How long does it take to increase bench press by 10kg?
For beginners, 10kg can come in 4-8 weeks with linear progression. For intermediate lifters, expect 8-16 weeks per 10kg increment. Advanced lifters may take a full training block (12+ weeks) for each meaningful gain.
Should I bench press every day to get stronger?
No. 2-4 sessions per week with adequate recovery is optimal for most lifters. Daily benching can work for advanced lifters but requires careful volume management.
Why is my bench press not going up?
The most common reasons: no true progressive overload, poor setup, insufficient tricep strength, or not enough weekly volume. Review all five keys above.
Does grip width affect bench press strength?
Yes. A wider grip shortens the range of motion and shifts load to the chest. Most Powerlifting Australia competitors benefit from gripping at or near the 81cm rings.
What are the best shoes for bench press?
A flat, stable sole is ideal for leg drive. The TurboLifter 3 Pro provides a non-compressible, flat platform that maximises leg drive force transfer during the bench press.
External Resources
- Powerlifting Australia
- Powerlifting New Zealand
- IPF — International Powerlifting Federation
- Strength & Conditioning Research
More Castiron Lift Strength Guides for Australian & NZ Lifters:
Written by T-K